Bialetti Brikka fix, repair and clean

by Jun 21, 2018diy-coffee27 comments

Bialetti Brikka Fix and Clean

My way to a better coffee…

Brikka is the brand name of a Coffee maker / Coffee pot / Stove pot / Macchinetta / Caffettiera made by Bialetti from Italy.

Brikka produces great Espresso (actually, Espresso-like beverage which is called Moka) with rich crema, much better than any other coffee pot. The innovation behind the Brikka is a small weight added to the brewed coffee exit which increases a bit the brewing pressure.

If you use the Brikka, Brikka2, Brikka-Elite coffee pot and use it correctly (*), you can trust it will serve you for long time without any needed maintenance out of washing it after each use.

(*) Correct use of Brikka means:
1. Using correct amount of water.  (Use the measuring container or fill up to the mark on the inside of water container)
2. Using water without or with very low degree of scale.
3. Using the right ground degree of coffee which is MEDIUM and not fine.
4. Filling the funnel with coffee WITHOUT pressing it.
5. Assembling the 2 parts (coffee and water containers) tightly.
6. Applying small and intense heat source that will not exceed the coffee pot base.

DISCLAIMER – Important!

Over the years Bialetti introduced several models of the Brikka coffee maker. (Brikka, Brikka2, Brikka-Elite)
Basically all models are the same with changes made to the cover/lid , its handle hinge and its funnel gasket.
Late models are supplied without a funnel gasket and with additional H2O water level marking inside the top container.
Each model comes in a 2-cups version and in a 4-cups version.

Solid lid model with center handle

Transparent lid model with center handle

Open lid model with side handle

After extensive usage or due to use of wrong ground coffee and/or scale water, your Brikka might get clogged, release pressure through the valve or between parts, use only part of the water etc. It will stop acting normally and will not produce your favorite espresso.

The reasons might be one or few of the following:
1. Clogged filter.
2. Worn filter gasket that does not allow pressure to build.
3. Clogged funnel.
4. Worn funnel gasket.
5. Clogged coffee center pipe that does not allow coffee to flow to upper container.
6. Clogged / stuck weight that blocks the coffee from flowing to upper container

If one of the above happens, it’s time you’ll send your Brikka to Bialetti’s service center or clean/repair it yourself.

First, let’s examine and get familiar with Brikka’s parts: (note: part 6 – Funnel gasket is not present in late models)

A. To clean the filter plate and check/replace the gasket:

Unscrew the water container and look at the bottom of the coffee pot top container. You’ll see the filter and the gasket.

Take the gasket and filter plate out and clean it thoroughly.

In order to take the gasket out, use a blunt knife edge or a small screwdriver and insert it between the gasket
and the filter plate (see image). Raise the gasket a bit and then pull it out. The filter plate will follow.
If the filter plate is stuck, use the screwdriver to lift it a little on one side and then it will be released.
To clean the filter plate, use an old toothbrush with liquid dish washing soap and make sure filter’s mesh is open.
If scale is clogging it, soak it for half an hour in warm vinegar and if this doesn’t help, soak it in Citric Acid solution (1 teaspoon of Citric Acid powder in one cup of room temperature water).

* Please note:
The use of dish washing soap / Vinegar / Citric acid is recommended only if you have a non functioning Brikka.
Regular cleaning of Brikka should be done with clean water only.

Check the gasket. If it is worn, too thin, dry or rotten, replace it.
Original replacement gasket can be obtained from Bialetti.
You can also use replacement gasket from 3rd party.

For the Brikka 2 cups, original gasket size is:
Outer diameter = 66.7mm (2″ 5/8), Inner diameter = 50mm (2″)
Any standard 3 cup coffee pot gasket (with outer diameter of ~ 65mm, 2-1/2”) is OK
For the Brikka 4 cups, any standard 6 cup coffee pot gasket (with outer diameter of ~ 70mm, 2-3/4”) is OK

Clean the lower part of the coffee container, especially the area where it meets the filter’s flange and the thread.
If needed, clean the coffee pipe from this side as well (see D).

When done, rinse in water and dry all parts. Assemble the filter plate and gasket to its place. Pay attention that the flanged part of the filter plate is facing toward the coffee container.

B. To clean the water container:

Check that the pressure valve is moving freely by pressing it from the inside.
If it’s stuck, use some force to release it and/or clean the container with warm vinegar
If this does not help, replace the valve! Don’t play with this unit as it is your safety that we are dealing with here.

Check and clean/remove scale from the container thread. It should be clean and free from any residue / scale.

If the internal bottom surface is stained and ugly looking, this is normal. It is oxidation of the Aluminum. You can clean it with Vinegar and if this doesn’t help, use Citric Acid solution (1 teaspoon of Citric Acid powder in one cup of room temperature water).
To avoid / reduce it, make sure the container is perfectly dry before you store it.

C. To clean / check the funnel:

Clean the funnel mesh with toothbrush as described above. Check that water flow freely if you fill it.
Check the funnel gasket, (Late models do not have gasket, so skip this section if you have a late model).
If gasket is worn, too thin, dry or rotten, replace it or replace the whole funnel with its gasket.
If you have a late model without a gasket, check the funnel flange surface consistency, if you find it is bent, you may add a funnel gasket or replace the funnel with a new one.

D. To clean the center coffee pipe and weight:

Remove the gasket and filter from the coffee container bottom part. (as described in section A)
Remove the weight upper part (11 in the drawing).
The weight is made of 2 parts, upper weight (11 in the drawing) and lower flange (10 in the drawing).
Upper weight is attached to lower flange by a screw thread.
Hold tight the lower flange (10) with one hand and rotate the upper weight (11) CCW (counterclockwise)
to release / unscrew it. You might need to use some force to do this.
Now after the upper weight (11) was removed, the pipe upper end is seen and you can clean it from both sides.
If needed, use hard wood teeth stick to clean/open the upper pipe hole. If scale is blocking the pipe,
use warm vinegar to remove it.
Check the weight’s inside gasket and thread and clean it. If gasket is worn, replace it.
When done, assemble the weight (11) to the weight flange (10).
Don’t use excessive force as you’ll want to be able to open it again in few months.
Assemble the filter plate and the gasket to the coffee container bottom part.

Now, when everything is clean and assembled, test your work.
Prepare an espresso and see if all is working as expected, coffee is flowing freely, crema is built and no pressure
leaks from the pressure valve or between water and coffee containers.

That’s all, we are done. Enjoy your coffee


Due to many questions about the correct water level for the Brikka, I added 2 images that show the recommended water level.
If your Brikka does not have that H2O protrusion in the upper container (with or without  the H2O text), use the following:

for Brikka 2: use 80cc (2.70 fl. Oz.) of water.
for Brikka 4: use 140cc (4.73 fl. Oz.) of water.

exclaim2 Never reach the safety valve!
Always keep the water level below the safety valve.

exclaim2 Don’t forget to transfer the water to the lower container!
Using the upper container is just for measuring the needed water quantity.

Comments, remarks and updates are welcome.
Some will be published, with hidden sender's details.

Did you find this article helpful?
Did it save you time and trouble?
If yes, please consider donating some $$$ to help me cover the hosting cost involved. Thanks

To make a donation, please click the following PayPal button:

Copyright © Schneor Design. All rights reserved. Do not copy without written consent from the author.


  1. jb

    coffee from my brikka won’t come out I check the valve and it’s moving freely, I don’t what happen, any suggestion? Thank you in advance.

    • Avi Schneor

      Hello, try to use a coarser grind coffee and don’t tamp it!
      Remember, you need to fully fill the basket.
      Good luck

  2. Jack R.

    What happens if you forget to transfer the water down. For me since I day I forgot to put the water down to the pot base. The brikka has stopped working and only steam comes out of the safety valve

    • Avi Schneor

      If parts were not burnt out, use it again but this time don’t forget the water!
      It should work fine. If gaskets are dry/deformed, replace them. Good luck

  3. Cody

    The safety valve I think has worn out. It shoots steam and doesn’t allow the pressure to build. Do you know where I can get a replacement relief (safety) valve for my Bialetti Brikka 4 oz?

    • Avi Schneor

      Check that 1. grinding is not too fine. Try to use coarser degree and test
      2. clean the valve while moving it in and out, it might be clogged.
      If this is not the cause try to look for the part in online stores.

  4. ML

    Avi, I recently started using a Moka pot which is older but was unused. It always leaked steam around the area where the two sections screw together. After using it for several weeks I decided to remove the gasket and clean it.. now when I use it it does not release steam from that area or the valve and that concerns me. It also has grounds in the bottom when I open it to clean it which never happened before. After reading many articles about using a Moka pot, I am scared to use it for fear of it exploding. What did I do to it that caused all of this?

    • Avi Schneor

      hey ML
      If your Moka does not leak between the parts and the safety valve is not releasing steam, than it is OK and coffee should flow to top part after heating it.
      When you find grounds in lower container, it usually means that the ground coffee is too fine. Use a coarser grind. Keep your Moka clean and always check that no grounds are left on bottom container edge prior of closing it. Have fun and good coffee.

      • ML

        Avi, Thank you for the reply. That makes me much more comfortable using my Moka pot. Here’s to a good cup of joe!

  5. A. Sol.

    Can you supply Filter Gaskets for the Bialetti 2cup and elite coffee makers.

    • Avi Schneor

      Thank you for your comment.
      I’m sorry but I do not supply any Bialetti parts.
      Please measure the gasket’s outer and inner diameter and search for it on online stores.
      You can easily find Bialetti replacement gaskets on Bialetti official store and on eBay, Amazon etc.
      Good luck


Submit a Comment

Your email address will not be published. Required fields are marked *

electric hazard sign


1. Brikka coffee pot works on heat and pressure.

Any modification made to your Brikka may cause damage to your equipment and harm to yourself or to others. 
Any modification made to your Brikka will void manufacturer warranty.
None of the following steps is recommended by me nor by the manufacturer, Bialetti. 
This post show only my personal experience and know-how.
If you follow any of the steps, you do it on your own risk and responsibility.

2. Copyright © 2011 Avi. All rights reserved. 

Content including all text and images in part or in whole may not be reproduced, retransmitted, stored, distributed, disseminated, sold, published, broadcast or circulated in any medium
without written consent of the author

You have Successfully Subscribed!

Pin It on Pinterest

Skip to content